In the recent 120k Q&A special you saw a clip of me standing in front of a red Lotus Elite, a few of you asked me about it, so here’s the start of that story.

Back in 2022 I went to look at a 1975 Lotus Elite. The car was sitting in an alley between two units on an industrial estate and although it had a good amount of paperwork documenting its life since new, that all ended with its last MOT in 2006. Between then and 2020 its life is a bit of a mystery, no records of anything happening, and it only gained around 100 miles on the odometer. So a lot of sitting about slowly returning to nature. In 2020 it was purchased by an individual who wanted it to be professionally restored, and extensively modified by a lotus specialist, but after getting the quote for the work and modifications near the 6 figure mark decided not to go ahead with the restoration and move the car onto some gullible idiot. A quick rundown of the vehicle’s condition was… interesting at best.

It has the original Elite chassis, although it had rusted to near nothing, full interior, although the headlining is sagging, the seats are growing mould and the driver’s seat has collapsed, and I still have no clue if any of the gauge’s work. The car still has its original Lotus 907 engine, which is in need of a rebuild, the passenger door will not open from the outside, the gearbox and fuel system are in unknown condition and the paint is faded, flaking off and a total mess. On the upside, it came with a whole host of spares, it has all the aluminium trim around the windows, three of the tyres held air for more than 24 hours and, although every inch of the car is tired, it was complete.

So, obviously, I did the only thing a reasonable, well-rounded financially responsible person would do, I agreed to buy the thing. The following weekend I returned to the aforementioned alley-way, gave the man an envelope of cash and proceeded to winch the car onto a trailer I had borrowed from my neighbour… of course, I don’t own a car with a tow hitch, so I’d also had to borrow a van from my other neighbour in order to pull the trailer. In preparation for the 120mile journey home, I had to remove some loose pieces of window trim, along with both rear side windows, as they were fairly loose, the windows have now temporarily been stuck back in to help keep water out as the car is stored outside under a car cover and I want to play it safe with water ingress.

With the car back home, and safely on the driveway, I set about emptying the car of the bags of spares (still needing to go through and see what I had), coating the interior with mould spray, and making plans to start the restoration. Before collecting the car, I managed to find a PDF of the Lotus Elite workshop manual, complete with exploded diagrams, instructions for servicing and repairing parts, along with a list of all the specialist tool that were available from the lotus factory back when the car was new.

Unfortunately, the original elite chassis were made of steel, and are not galvanized from the factory, simply painted. Lotus, in their infinite wisdom, then use wool as an insulation and sound deadening material between the chassis and fibreglass body. The wool then absorbs water, which then in turn rots out the chassis. This is a common and well document issue with these cars. In the final production years, they did start galvanizing the chassis, which solved the issue.

So, with the above in mind, it was time to make a plan. I know the entire car needs work, so, the easiest way for me to tackle this is to break it down into the different main sections:

Body – this will need fully stripping back, cracks in the fibreglass need repairing, and then the whole body needs repainting. Part of repainting the body will mean removing all the glass, this isn’t a massive issue, however the windscreen is surrounded by aluminium trim, the top and bottom pieces of which are incredibly thin, and stuck to the car with the same adhesive they used on the windscreen, I’ve been reliably told that there is a 90% chance they will get damaged in removal, replacement trims are nearly impossible to find, usually damaged, and was given a quote from a specialist of £400 PER TRIM for damaged ones.

Interior – at best needs a full re-trim, likely needs new padding too. The driver’s seat is fully collapsed, so this needs replacing.

Electrical – untested, assumed to need fully re-wiring, which is fun, given I’m awful at wiring.

Driveline – The engine will need a rebuild, having a look in the cylinders shows some rust on the cylinder walls, but they are fully aluminium engines with cylinder liners, so not a massive issue. The gearbox is untested, but the original elite gearboxes are known to be weak.

Chassis – honestly, the chassis is scrap. The rust is so bad one of the suspension towers is no longer attached, with an incredible amount of very skilled welding it could be saved, but it is not economically viable. It is possible to buy a galvanized reproduction chassis, but these are very expensive and would still need all the suspension and other components. The third option, and the one I chose, is to swap the elite onto a chassis from a lotus excel, this is a fairly common swap on these cars, however so far I have not found a well-documented “how to” post, but a rolling chassis can be had for not too much investment, and a full box of parts to rebuild it can be had for about the same money.

So, with the condition of the car’s main sections identified, a plan was formulated,
step 1: Replace and Rebuild Chassis.
Step 3: Get it running.
Step 4: electrical.
Step 5: replace the interior.
Step 6: make it look good.

Just like that, with only 6 basic steps I’ll have myself a classic low production British sports car, what could be more simple… or… something like that anyway.

Well, now the plan is in place, next came the teardown and chassis replacement. But that seems like something for a future blog post. Thanks for reading!