Well then, it’s been a few weeks, but I guess it’s time for the next instalment of the lotus restoration story. Last time I talked about how I acquired such a piece of fine automotive history, its condition upon getting it home, and the plan to get it back on the road. So, we know the first job, is to replace the chassis, in order to do that I need to lift the body off the old chassis. Now, for some of you, this may seem like an easy task, simply unbolt the body from the chassis, roll the car onto a two-post lift, put the lifting arms under the body and lift away, leaving the chassis on the floor and the body on the lift.
Ahhh, if only it were so easy. Firstly, I lack a lift, of any kind. I have a standard trolley jack, a couple of bottle jacks, and a set of axle stands. But that’s not going to lift the body the three or four feet needed in order to clear the chassis. The other consideration to be made is the engine. The lotus has a somewhat unconventional engine as it sits in the car leaning over at 45 degrees towards the passenger side with the valve cover being very close indeed to the wheel arch. I am reliably informed that the easiest solution is to leave the engine in place, bolted to the chassis, and lift the body off over the engine, so no problems there then…
In addition to the issue above, once I’ve separated the body from the chassis… where do I put them? I only have a single car driveway, and whilst there is a small garage half of it is used as a small workshop, and the other half is used as storage for all those household things you don’t often need, pushbikes, folding chairs and the like.
Well dear reader. The solution to both these problems is simple. Scaffolding! So, with some scaffolding poles and a 2 ton chain block, we made a crane! But, how do we attach the crane to the body of the car. Okay, here goes, so, the first step is obviously, unbolt the body from the chassis, then, we used a couple of bottle jacks to lift the body of the car off the chassis, clocking the body up on bricks, lowering the jacks, putting the jacks on a smaller tower of bricks, before lifting again. However, about 4 inches in, we had a problem. The inner wheel arch of the body was fouling the valve cover on the engine. But how, the specialist said it would clear… well, after much crawling around on the floor, poking, prodding and general investigation it turns out, the rubber engine mounts were so excessively perished that the engine was leaning over more than normal, causing it to block the body from being lifted. So, time for a change of plan.
I guess we’re taking the engine out through the engine bay before lifting the body. This should be simple… in theory, disconnect all the hoses, wires and cables connected to the engine, borrow an engine crane from a friend, and with a bit of elbow grease the engine’s out! Or… so I’d hoped. As it turns out the engine crane has a leaky seal somewhere, meaning in total we only get about 60% of the total lift height it should be able to achieve, as such, it’s not able to lift the engine enough in order to get the angle to pull the engine and gearbox out together. So, engine back down, lift the front of the car in the air, crawl under the car, unbolt the gearbox from the engine, drop the gearbox onto my chest (which definitely didn’t hurt at all and was a good idea), drag roll and crawl myself and the gearbox out from under the car, and finally put the car back down. With that done, the engine came out smooth as butter.

At this point, I also had a realization, in order to get the body off, I don’t need to lift the body as high as I originally thought, I can easily lower the height of the chassis by a good 6 inches by simply taking the wheels off, and putting the chassis on the floor. Something generally considered a bad idea as it could potentially damage brakes, suspension components and crush fuel and brake lines. But, all of this would be replaced, along with the chassis.
So, that’s what I did, dropped the chassis to the floor, and I was then able to get enough height on the axle stands and some scaffolding boards to lift the body just clear of the chassis, this then allowed me to slide some scaffolding boards across under the body from left to right, which I looped some 1 ton straps too before hooking them to the chain block and well… up the body went. A full 5ft into the air. Where it was then placed on a structure of trestles, scaffolding boards and the brick wall between my driveway and my neighbour’s garden (I’m very lucky to live next to such an understanding… or at least slightly bemused and very tolerant person)

With the body removed, hidden under its cover, and safely “stored” until its next needed. The full extent of the damage to the chassis can be seen, in the photo above alone you can see the missing suspension tower, along with some of the extent of the rust.
I think this is enough of me prattling on for one week, the body and chassis have been separated, the engine and gearbox are safely sat on the garage floor (ready and waiting for the engine stand to arrive) and the chassis is well and truly rotten. Thanks for reading my ramblings!